Welcome... and Warning:
Because I seem to have “an ax to grind” with many folks (some fellow ax nuts, some nuts in other ways), perhaps I ought to apologize beforehand for any ego-harm some of my comments (plus unintended prejudices and bias) in the discussions below may cause.
Rest assured, however, that my intent here is to elevate the potential usefulness of an ax – one of the tools which, as the future unfolds, I believe we will be glad that we know how to apply seriously and efficiently.
At the same time I wholeheartedly welcome constructive criticism, of course.

February 22, 2011

Straight versus Curved

“The most baneful defect of the modern single-bitted ax handle is its short bottom curve. The lower end is the grip where the chopper guides the ax. The grip portion bends from the adjoining shaft of the handle by about 10 degrees. Unfortunately, this pretty little curve magnifies the effect of wrist pivoting...


"The axis of pivot for a straight-handled ax lies in the center of the handle throughout its entire length from end knob to top side of the eye.

"But with the curved handle, any rotation is controlled by the chopper’s hands grasping the lower curve at the grip. Therefore the real axis of pivot does not pass through the ax head at all because the 10 degree bend of the lower handgrip is not pointed in that direction. The effective and real axis lies in an extension of the grip and passes somewhere to the rear of the entire axhead.

"The trouble-making grip with its 10 degree bend subtends an arc of 4½” at the handle's residual length of 25".  That means that the curved-handle axe already has a constructive "foresection" of 4½” behind what we have hitherto termed the “axis of pivot”. But there is also an additional 4½” waiting at that point. Remember, we stated that each ax has a fore-section distance of 4½” forward of the axis of pivot (by the string-suspension method). For  curved-handle ax then, the constructive fore-section length between the real axis of pivot and the bit is: 2x4½”, or 9”.

"So the ax with a curved handle will act as if it had an imposing bit 9” long. For a rotation of only 5 degrees, its bit will swing .78”, exactly twice what that same ax would deviate if hung on a straight handle. Greater rotation would bring greater deviation in the same proportion. This is the most damning case against the curved handle. It is substantially less accurate than a straight handle.

"However, the human body is a marvelous machine. It can adapt to nearly anything. If the handle of a golf club were shaped like a pretzel, some people would still play golf. A chopper soon adapts himself to a curved ax handle even though that handle is designed to frustrate accuracy. The chopper acts as if there were a straight axis throughout the entire length of the handle, even though there is not.

"But this unconscious adaptation has a price. Use of the curved handle requires more practice to cut well. And even with practice, the chopper cannot attain the results possible with a straight handle. In our history, this is at least partially confirmed by the woods professionals of the era when trees were felled with axes. These men graduated from single-bitted axes on straight handles to double-bitted axes, also on straight handles. Curved ax handles do not seem to have ever attained widespread professional acceptance."

-- Dudley Cook


Source:

Drawings and text from Keeping Warm with an Ax:  A Woodcutter's Manual, by D. Cook, 1981, Universe Books, pages 89-90.

Currently published as The Ax Book: The Lore and Science of the Woodcutter by Dudley Cook, illustrated by S. Lawrence Whipple.  
Published by Alan C. Hood & Company, www.hoodbooks.com


Used with permission.




February 16, 2011

"Weak" handles



Much of the handle-related discussions (at least in the forums I have read) concern grain alignment. Yes, that is a pertinent strength-related issue, and I certainly agree that the closer a handle maker can come to the vertically positioned and continuous grain, the better.

However, I want to present an additional question – one already partially addressed in my views pertaining to handle dimensions. To frame this question within the context of a discussion about axes, it may go something like this:

How weak can an ax handle be (and still prove itself useful)?

Here is another true story:

The exact year when I made the handle in the photos (above and below) has now faded from my memory, but it was sometime soon after we obtained Keeping Warm with an Ax (by D. Cook) which puts it about 15 years ago.


Note that the handle is relatively straight near the bottom end (already Dudley Cook’s influence?), yet I also wanted to retain that “head slightly back of the line of grip” feature which many old axmen incorporated into their single bit handle design. The easiest way to accomplish this, and still end up with a through-running grain (which most single bit handles do not have nowadays) is to find a naturally grown piece of wood in already that shape.

Without exception, every instructional source on ax handle making I’ve come across suggests that you begin by selecting a piece of straight grained tree trunk, 8 inches (20cm) diameter or larger, split out the billets, season them, etc.

Well, mindful that (sometimes) “rules are made for fools”, I stuck as much as possible to the continuous grain concept -- but in every other aspect broke the rules. That handle is made out of a non-seasoned branch less than 3 inches diameter from a white birch tree which I had just cut for firewood. It had exactly the curve I was looking for, so I shaped it still green, fit that 1¾ lb (800g) Sandvik head to it, gave it a coat of boiled linseed oil (cut with a little turpentine) and began to use it – carefully at first. I liked that handle instantly. At its slimmest section it is 18mm thick, by the way.

About two years later, during winter, I lost that ax in the woods. There it laid for a season and a half, in snow, wet leaves and snow again. When I found it the following spring, some fungus was beginning to make a Slow Food meal of it. (Note the surface wood deterioration below the head on the side which had been touching the Earth.)

As some of you may know, white birch (Betula alba) is not a particularly weather resistant wood; in fact, some would say it is absolutely “no good” in that respect. Having once been oiled, and already seasoned before being lost did help its survival – but some damage was there to stay.

Nevertheless, we’ve used that little ax rather extensively ever since. Occasionally, it has (again forgotten) spent an additional night under the stars...

The chief point of this story: A functional ax handle does not always need to be made of what is considered first class wood. The handle being discussed here has 3 major knots (seen from both sides) and 2 minor knots – a flaw that every handle-making how-to source would consider a serious no-no. In addition, white birch is considerably weaker than ash or sugar maple, never mind hickory.

Admittedly, a 1¾ lb head on a 24” handle (which probably started as 25”) is not a serious tree-chopping or firewood splitting ax – and thus does not need to be excessively strong. However, we do not baby our axes (as might some weekend campers with their $100 hatchets) – and this little “orphan” has done its full share of what I’d expect of that size of an ax.

To be continued...




February 13, 2011

The Devolution of Axe Handles


To cut across the grain of what appears to be popular, I choose to focus first on the blunt rather than the sharp end of the ax.

You see, in many cases a truly good (meaning well-designed and sized) handle can effectively elevate the efficiency of a tool’s working edge. Conversely, a fine tool’s potential can quickly be depreciated by fitting to it a poor handle.

These are facts most experienced tool users would agree with, period. Yet, the numbers of “top of the line” blades outfitted with what I’d refer to as “bottom of the line” handles is large indeed. In the case with axes, that number is growing steadily... or I should say, alarmingly. (The number I am talking about is a percentage of axes sold and/or used -- which today is many less than in the past, of course.)

Therefore, as a subset of ax-related discussion, I begin with the issue of handles. 

Reflecting on the devolution of ax handles – and how to refine (up to a point) the abominations many of you end up buying nowadays:

First, a true short story:

A few days ago I arrived from town with a parcel which contained, among other things, a couple of new axes we wanted to test. Faye and Ashley were already in bed so I quietly opened the box, took out a sample of each item to quickly look at, and left them laying on the kitchen table.

As I awoke the next morning I heard Ashley exclaim, “Oh my God!"

In spite of my “half-here and half still gone” stupor, I instantly knew that she was holding one of the axes, and also that her unspoken thought was “these are such clubs!” She was referring to the ax handles – and justifiably so. These were the bulkiest handles I’ve yet seen on axes sold in North America. For an 8 pound splitting maul some people (not me) might consider them “OK”. But these here were stuck into 1 ¾ and 2 ½ pound heads...

The photo below is meant to demonstrate the devolution. It is, in fact, a brief documentation of history, because what you see here are commercially-produced ax handles, purchased in Canada  between 1975 and 2011. All of them are hickory. (To further qualify, the third handle is a version possibly turned in Sweden -- and sold globally on what presumably is one of the “hand-forged” connoisseur axes today.)

Here (from left to right) are their respective dimensions and weights of the heads they came with:

1. (1975) – 18x32mm, 31 inch long, head 3 ½ lb (my very first ax)
2. (1995) – 23x37mm, 27 inch long, head 2 ¾ lb
3. (2010) – 26x 39mm, 26 inch long, head 2 lb
4. (2011) – 29x40mm, 27 inch long, head 2 ½ lb

















  























“What’s the problem?”, some people may exclaim, “if anything, we are getting progressively more wood (and presumably strength) for the money”. Well, yes, there is nearly twice the volume of wood in each foot of the 2011 as opposed to the 1975 handle. However, as I hope to explain below, this is clearly a case of “too much of a good thing”...

During the 35 years of living in New Brunswick, Canada, I’ve come to appreciate the local old timers’ love for slim and limber handles (examples to follow). These now 80-90 year olds, who did grow up with an ax in their hands so to speak, consider contemporary “boughten” handles way too clumsy and oversize, fit perhaps for a pickax but not a wood chopping ax.

In the photo below you see three locally made handles with the 2011 “white elephant” in-between. While measuring these three (for the purpose of this piece) I was surprised that their cross sections were exactly the same –16x33mm!

The respective lengths and weights of these axes are (from left to right):
32” (sugar maple) with single bit 3 ¼ lb head
27" (hickory) with single bit 2 ½ lb head
29” (ash) with double bit 2 ½ lb head
29” (ash) with single bit 2 ¼ lb head




A good ax handle needs some spring to it, the old-timers say, or a man gets “all beat up” in a day of chopping. To fully appreciate what they mean, one may have to get serious about ax work, and use the tool more extensively than most folks do nowadays.

Yet, I think that if most of you out there tried to chop for only 10 minutes with the exact same two ax heads, one fitted with that 1975 and the other with the 2011 handle, you would want to take home the older, and leave the modern version behind...

Besides the inevitable jar that a thick handle gives to the user’s body when the steel head on its end contacts solid wood, there is another benefit of a slimmer design. By “slim” I am referring  primarily to handle’s thickness, not width -- the latter being the larger of the two numbers given in the dimension above. Because, if the overall wood volume in “a limber handle” was of a perfectly round shape, it could still be called  “slim” and indeed function well enough as a shock absorber. HOWEVER (beside being weaker than an oval) it wouldn’t help the chopper’s accuracy to the extent that a handle should.

The “flatness” of a good handle provides an effective reference between the hand and the ax’s edge – ( which is one reason why the handles of many other tools have an oval rather than round shape). A thicker (and usually more rounded) profile requires more squeezing to achieve equivalent effect... and when a body focuses on squeezing, it inevitably loses some of its potential to center. Centering leads to accuracy and accuracy is what effective wood chopping is about...

To sum up: 
AX HANDLES SHOULD BE FLATTER THAN MOST OF THEM ARE.

Now, there are two other features of ax design that significantly effect accuracy. One of them is related to the shape of the head, and it will be addressed later. The other will keep us on the issue of handle design a little longer.

The notoriously popular curvature in the bottom end of single-bitted ax handles is one of those insidious aspects of ax design in general that people have accepted without realizing that by using it they are (sort of) “working against themselves”, so to speak.

For quite some time before we came across Dudley Cook’s "Keeping Warm with an Ax" (the new edition’s title is “The Ax Book”), I had noticed that I could not do as well with axes the handles of which sported this curve. I could not put my finger on exactly where the problem laid – but Dudley explains it all very well. Hence I now turn to him for help:

“The most baneful defect of the modern single-bitted ax handle is its short bottom curve. The lower end is the grip where the chopper guides the ax. The grip portion bends from the adjoining shaft of the handle by about 10 degrees. Unfortunately, this pretty little curve magnifies the effect of wrist pivoting...

"The axis of pivot for a straight-handled ax lies in the center of the handle throughout its entire length from end knob to top side of the eye.

"But with the curved handle, any rotation is controlled by the chopper’s hands grasping the lower curve at the grip. Therefore the real axis of pivot does not pass through the ax head at all because the 10 degree bend of the lower handgrip is not pointed in that direction. The effective and real axis lies in an extension of the grip and passes somewhere to the rear of the entire axhead.

"The trouble-making grip with its 10 degree bend subtends an arc of 4½” at the handle's residual length of 25".  That means that the curved-handle axe already has a constructive "foresection" of 4½” behind what we have hitherto termed the “axis of pivot”. But there is also an additional 4½” waiting at that point. Remember, we stated that each ax has a fore-section distance of 4½” forward of the axis of pivot (by the string-suspension method). For  curved-handle ax then, the constructive fore-section length between the real axis of pivot and the bit is: 2x4½”, or 9”.

"So the ax with a curved handle will act as if it had an imposing bit 9” long. For a rotation of only 5 degrees, its bit will swing .78”, exactly twice what that same ax would deviate if hung on a straight handle. Greater rotation would bring greater deviation in the same proportion. This is the most damning case against the curved handle. It is substantially less accurate than a straight handle.

"However, the human body is a marvelous machine. It can adapt to nearly anything. If the handle of a golf club were shaped like a pretzel, some people would still play golf. A chopper soon adapts himself to a curved ax handle even though that handle is designed to frustrate accuracy. The chopper acts as if there were a straight axis throughout the entire length of the handle, even though there is not.

"But this unconscious adaptation has a price. Use of the curved handle requires more practice to cut well. And even with practice, the chopper cannot attain the results possible with a straight handle. In our history, this is at least partially confirmed by the woods professionals of the era when trees were felled with axes. These men graduated from single-bitted axes on straight handles to double-bitted axes, also on straight handles. Curved ax handles do not seem to have ever attained widespread professional acceptance."

(From "Keeping Warm with an Ax, A Woodcutter's Manual", by D. Cook, 1981, Universe Books, page 90)

(An excellent illustration from this book appears 
in the February 22 post titled "Straight versus Curved".)

There you have it – try a straighter (as well as slimmer) handle; you will likely enjoy the ax-work more and also be more efficient!

Refining commercial handle models:       

Commercial (that is, lathe-turned) handles do come in a variety of shapes. Most of them sport the curve near the grip. The handle supplied with the "Trail Boss" (far left in the photo below) is one of the few exceptions.


To slim down a thick handle is a relatively easy task. To straighten that devilish short curve near the knob is another matter. When the curve is as pronounced (and the overall amount of wood not excessive) – as in Example 4. – no alteration is realistically possible. On the other hand, the Example 2 can be made almost  completely straight (as we will show in a later post). Example 3 is somewhere in-between, while the lower handle curvature on #1 (the "Trail Boss" on the far left) is good as is.





February 11, 2011

Introduction

As a little background, I grew up in Slovakia, where, as in most of Europe, ax design has lagged behind America a century or two, both in terms of heads and handle shapes. (Many handles there still do not have a knob, for instance.) That is not to say that Europe lacks good ax-men, but by the time I left (at the age of 18) I certainly wasn’t one of them.

Only since about the early nineteen eighties have I become a serious ax user. This still does not imply that I am, as the old timers around here would put it, “a good man with an ax”. For that I was already too old when I first really fell in love with this wonderful tool. One almost has to “grow up with an ax in hand”, they say, to become a real ax-man (or an ax-woman, I suppose, in these unisex days). What I mean by “serious” is that on our homestead we’ve long used axes (during certain periods of a year almost daily) for many tasks – from felling and limbing trees, hewing logs and notching them, making tool handles and, of course, that still most prevalent use of an ax today – splitting firewood.

In addition, I’ve had an interest (sometimes nearing an obsession) in comparing the utility of various versions/models of the tool that strikes a chord with me, and the ax has been the second (after the scythe) to consume my attention. Consequently, I’ve restored several dozen of (mostly vintage USA and Canada-made) axes from a $2 to $5 garage sale condition to a newly-handled tool, tested out during a variety of  work. All this does NOT make me an ax “expert”, though I believe there is a useful opinion or two I can share with budding ax enthusiasts...